SikaTop-107 Seal KH

SikaTop-107 Seal KH | Two component cementitious slurry for waterproofing and damp proofing

DESCRIPTION

SikaTop-107 Seal KH is a two part polymer modified cementitious waterproof mortar slurry comprising of a liquid polymer and a cement based mix incorporating special admixtures.

SikaTop-107 Seal KH suitable for drinking water, wet room and swimming pool system.

USES

• Interior and exterior waterproofing and damp-proofing of concrete, cementitious rendering, brickwork and blockwork
• Cementitious waterproofing for drinking and portable water, wet room and swimming pool system
• Rigid waterproofing of basement walls in new construction and refurbishment
• Pore / blowhole filling
• Waterproofing basement
• Sealing fine “hairline” cracks in concrete structures (not subject to movement)
• Levelling mortar for concrete repair works

CHARACTERISTICS / ADVANTAGES

• Approved for potable water contact
• Protects against water penetration
• Easy to apply by brush, thin trowel applications
• Hand or spray applied
• No water required / Prebatched components
• Easy and fast mixing
• Very good adhesion
• Protects concrete against carbonation
• Non-corrosive to steel or iron

PRODUCT INFORMATION

APPLICATION INFORMATION

BASIS OF PRODUCT DATA

Important Considerations:

• SikaTop®-107 Seal KH is not a decorative treatment, and it may display “blooming” after rain or in damp weather. This doesn’t affect performance.
• Avoid application in direct sun or strong wind.
• Do not add water under any circumstances.
• Apply only to sound, prepared substrates.
• Do not exceed the maximum layer thickness.
• For waterproofing or damp-proofing, always use at least 2 coats for a total thickness of 1.5 to 2.0 mm. In areas of severe water penetration, three coats might be needed.
• Protect freshly applied material from rain.
• When waterproofing/damp-proofing, take care not to puncture the waterproof coating with fixings. Use surface bonding with products like Sikadur® -31 CF Normal or Sikaflex® Construction (AP), etc.

Ecology, Health, and Safety: Ensure compliance with safety and environmental regulations.

Application Instructions:

Substrate Quality/Pre-Treatment:

• The substrate must be structurally sound and free from contaminants, loose particles, cement laitance, oils, and grease.
• Tensile adhesive strength of the concrete must be > 1.0 N/mm².
• Prepare the substrate using suitable mechanical techniques like high-pressure water jetting, needle guns, blast cleaning, etc.
• Pre-wet the surface to a saturated surface dry condition.
• For pore/blowhole filling, blast clean to remove all contaminants.
• For use as a levelling mortar, remove surface contamination and expose blowholes and honeycombed areas. Profile the surface for better bonding.

Mixing:

• Mechanically mix SikaTop®-107 Seal KH for 3 minutes using a forced action mixer or a clean drum with a drill.

Application:

• Shake Part A before use. Pour about half of Part A into a mixing container and add Part B slowly while mixing.
• Continue mixing until a uniform, lump-free consistency is achieved. The surface must be slightly pre-wetted.
• For slurry application, apply the mixed SikaTop®-107 Seal KH either mechanically by spray or by hand using a stiff brush, applied in the same direction.
• Apply the 2nd coat of SikaTop®-107 Seal KH in a crosswise direction to the first application once the first coat has hardened.
• When using it as a mortar and applying by trowel for a smooth surface finish, mix it with a 10% reduction of Part A (~1 A : 4.5 B).
• Apply the 2nd coat as soon as the first coat has hardened.
• For pore/blowhole filling, tightly trowel the product into the pores/blowholes of the surface.

Local Restrictions: Be aware that specific local regulations may affect product data and recommended uses. Consult the local Product Data Sheet for precise information and use guidelines.